One of the great benefits of calcined clay is that it activates at a much lower temperature than that required to make clinker. With temperatures of 750 – 850˚C instead of 1400 – 1500˚C and much lower costs for grinding and handling, you gain significant fuel and power savings – 30% and 40%, respectively – when comparing the operating cost to make 1 tonne of clay versus 1 tonne of clinker. While this is obviously a great result for the environment, it also makes for much lower operating costs, enabling you to achieve a reduced cost per tonne of cement.
Table 1 summarizes a direct comparison between two common type of cements, the traditional OPC and LC3, in which 30% of the limestone is replaced by clay. The impact is clear: 40% lower CO₂ emissions per tonne of cement. And that is without considering the further reductions you could gain if you also switched to more environmentally-friendly fuels.
|OPC (95% clinker / 5% gypsum)||LC3 (50% clinker/
15% limestone /
30% activated clay / 5% gypsum)
|Fuel consumption kcal/ kg cement||684||468*||>30% decrease in fuel|
|Power consumption kWh/t||85||51||~40% decrease in power|
CO₂ reduction kg/kg cement
|Total CO₂ emission kg/kg||0.82||0.47||>40% decrease in CO₂|
|Cement capacity index||100||100-190||Make more cement with same clinker, or same cement with less clinker|
* Based on 15% moisture and 10% LOI in the raw clay
** excludes carbonate and organic content in slay (traces may be expected)
*** excludes "neutral" CO2 fuels
Reasons to use calcined clay to reduce your clinker factor
- Up to 40% CO₂ emissions reduction per tonne of cement
- 30% reduction in power consumption per tonne of cement
- 40% reduction in fuel consumption per tonne of cement
- Increase productivity without increasing emissions
- Worldwide availability
- Maintain cement quality with much-reduced environmental impact
- Technology is proven and available now, with high ROI and low OPEX
Managing the risks of a new investment
With any new technology, there will always be some hesitation. Being an early adopter carries risks as well as benefits. But having dedicated ourselves to equipping the cement industry with the means to achieve net zero, we want to give cement manufacturers the confidence that they are investing in solutions that will work for them. That’s why we set up a pilot plant in our test facility in Denmark, specifically dedicated to calcined clay.
Here, we can carry out full chemistry and mineralogical testing of your clay source, as well as a clay reactivity analysis. We can also put your clay through our pilot test system, including crushing/drying, calcining, colour control, strength testing, etc. to show that the clay will meet the strength and colour requirements of a blended cement for ultimate peace of mind before making an investment.
This facility was instrumental in the decision by French cement manufacturer Ciment Vicat to invest in a 525 tpd clay calcination plant, which will be built in France. Citing increasing demand for sustainable cements as one of their main drivers, Ciment Vicat approached us with the project knowing we had the ability to confirm the suitability of their locally available clay source. We tested 5 tonnes of clay and were able to give them the reassurance they needed to proceed with the investment.
“We are excited and proud to be setting a new standard for green cement in Europe”
The Ciment Vicat projectCiment Vicat has ordered Europe’s first full-scale clay calcination plant. It will have a design capacity of up to 525 tpd and be located at their site in Xeuilley. The scope of the contract with FLSmidth includes a clay feeder, dryer crusher, calcination tower and gas emissions abatement equipment. In addition, the project also includes the facilities needed for alternative fuels handling. Altogether, the company expects both a financial and environmental return-on-investment from lower CO₂ emissions, fuel savings and reduced clinker ratio.
One decade to make a difference
Calcined clay is a stable, widely available resource that slots in easily to the existing cement manufacturing process. It requires new but familiar technologies. It produces a different but equally high-quality cement product, at a lower cost, using less energy and less fuel. It has the potential to dramatically reduce the cement industry’s environmental impact.
What are we waiting for? FLSmidth is ready to assist with your clay calcination plans and to help answer any questions or concerns you might have. This is our decade to make a difference. We can reduce the pressure on our industry and on our planet by moving the cement industry over to a more environmentally friendly cement product as standard.